Журнал Российского общества по неразрушающему контролю и технической диагностике
The journal of the Russian society for non-destructive testing and technical diagnostic
 
| Русский Русский | English English |
 
Главная Архив номеров
29 | 03 | 2024
2016, 03 март (March)

DOI: 10.14489/td.2016.03.pp.009-013

Бахматов П.В., Тишкова Е.Е., Бажин В.И.
К ВОПРОСУ ОЦЕНКИ НАПРЯЖЕННОГО СОСТОЯНИЯ СВАРНЫХ СОЕДИНЕНИЙ
(c. 9-13)

Аннотация. Рассмотрен подход к оценке механизма образования сварочных напряжений с позиции общего анализа результатов дилатометрии основного и наплавленного материалов с определением температуры начала и конца полиморфных превращений, а также изотерм распределения температурных полей, намечены пути снижения сварочных напряжений. Проведен анализ объема наплавленного и основного металлов в составе сварного соединения.

Ключевые слова:  напряжения в сварных соединениях, изотермы распределения тепла от сварочной ванны, дилатограммы.

Bakhmatov P.V., Tishkova E.E., Bazhin V.I.
ON ASSESSMENT STRESS WELD CONDITIONS
(pp. 9-13)

Abstract. It analyzed the amount of the deposited and base metal in the composition of the welded joint. It is found that the properties of welded joints, including thermal, are determined when the arc welding methods used by the filler material, which often do not coincide with those of the base metal. It is dealt with an approach to evaluate the formation mechanism of the welding voltage from the position of a general analysis of the main results of dilatometry of the deposited and base metal with definition of a certain temperature of the start and end of polymorphic transformations, as well as the distribution of temperature fields isotherms. This analysis allows to graphically visualize and evaluate the volume of the base metal and weld metal undergoing polymorphic transformations from the standpoint of selection of welding materials and welded with respect to forecast the degree of residual stress in welded joint. It is proposed the ways of reducing the welding stresses.

Keywords: stress in welded joints, the isotherm distribution of heat from the weld pool, dilatometric curves.

Рус

П. В. Бахматов, Е. Е. Тишкова, В. И. Бажин (ФГБОУ ВПО «Комсомольский-на-Амуре государственный технический университет», Комсомольск-на-Амуре, Россия) E-mail: Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.  

Eng

P. V. Bakhmatov, E. E. Tishkova, V. I. Bazhin (Federal State-financed Educational Institution of Higher Professional Learning “Komsomolsk-na-Amure State Technical University”, Komsomolsk-na-Amure, Russia) E-mail: Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.  

Рус

1. Муравьев В. И., Бахматов П. В., Дебеляк А. А. Определение возможности расчета остаточных деформаций по тепловым полям при сварке тонких пластин встык // Ученые записки КнАГТУ. 2010. № IV-1(4). С. 68 – 80.
2. Муравьев В. И., Бахматов П. В., Дебеляк А. А. Расчет остаточных деформаций при сварке тонких пластин встык // Сварочное производство. 2012. № 2. С. 9 – 12.
3. Рыкалин Н. Н. Расчеты тепловых процессов при сварке. М.: Машгиз, 1951. 296 с.
4. Шоршоров, М. Х., Белов В. В. Фазовые превращения и изменения свойств стали при сварке / М. Х. Шоршоров. М. : Наука, 1972. 220 с.
5. Грабин, В. Ф., Денисенко А. В. Металловедение сварки низко- и среднелегированных сталей. Киев : Наук. думка, 1978. 276 с.

Eng

1. Murav'ev V. I., Bakhmatov P.V., Debeliak A. A. (2010). Determining the possibility of calculating the residual deformation on thermal fields when welding thin plates end to end. Uchenye zapiski KnAGTU, IV-1(4), pp. 68-80.
2. Murav'ev V. I., Bakhmatov P. V., Debeliak A. A. (2012). Calculation of residual deformations of the plates in end to end welding. Svarochnoe proizvodstvo, (2), pp. 9-12.
3. Rykalin N. N. (1951). Calculations of thermal processes in welding. Moscow: Mashgiz.
4. Shorshorov M. Kh., Belov V. V. (1972). Phase transitions and change of the properties of steel for welding. Moscow: Nauka.
5. Grabin, V. F., Denisenko A. V. (1978). Metallurgy of welding of low and medium alloy steels. Kiev: Naukova dumka.

Рус

Статью можно приобрести в электронном виде (PDF формат).

Стоимость статьи 350 руб. (в том числе НДС 18%). После оформления заказа, в течение нескольких дней, на указанный вами e-mail придут счет и квитанция для оплаты в банке.

После поступления денег на счет издательства, вам будет выслан электронный вариант статьи.

Для заказа статьи заполните форму:

Форма заказа статьи



Дополнительно для юридических лиц:


Type the characters you see in the picture below



.

Eng

This article  is available in electronic format (PDF).

The cost of a single article is 350 rubles. (including VAT 18%). After you place an order within a few days, you will receive following documents to your specified e-mail: account on payment and receipt to pay in the bank.

After depositing your payment on our bank account we send you file of the article by e-mail.

To order articles please fill out the form below:

Purchase digital version of a single article


Type the characters you see in the picture below



 

 

 

 

 

.

.

 

 
Поиск
На сайте?
Сейчас на сайте находятся:
 32 гостей на сайте
Опросы
Понравился Вам сайт журнала?
 
Баннер
Rambler's Top100 Яндекс цитирования