Журнал Российского общества по неразрушающему контролю и технической диагностике
The journal of the Russian society for non-destructive testing and technical diagnostic
 
| Русский Русский | English English |
 
Главная Архив номеров
28 | 03 | 2024
2015, 11 ноябрь (November)

DOI: 10.14489/td.2015.011.pp.041-048

Кондратенко Е. В.
АНАЛИЗ ИСПОЛЬЗОВАНИЯ ПРОГРАММНОЙ СРЕДЫ ДЛЯ РЕШЕНИЯ ЗАДАЧ ИСТЕЧЕНИЯ ГАЗА СКВОЗЬ МАЛЫЕ ОТВЕРСТИЯ
(с. 41-48)

Аннотация. Рассмотрена возможность использования CAD-программ на примере SolidWorks для расчета потоков газа и анализа характерных особенностей течения на выходе из течи. Выполнен анализ параметров истечения ряда классических моделей течей типа пор – прямые каналы круглого сечения (цилиндрические) и течей типа щелей и трещин – вытянутые каналы прямоугольного сечения (щелевидные). Показано, что расчетные значения характерных параметров достаточно хорошо совпадают с известными экспериментальными данными.

Ключевые слова:  сквозной дефект, скорость движения газа, SolidWorks.

 

Kondratenko E.V.
ANALYSIS OF USE OF THE SOFTWARE ENVIRONMENT FOR SOLVING PROBLEMS OF GAS OUTFLOW THROUGH SMALL HOLES
(pp. 41-48)

Abstract. This article discusses the possibility of using CAD-programs at the example of SolidWorks for calculation of gas flows and analysis of the characteristics of gas flow at the outlet of the leak. The analysis of the parameters of expiry for a number of classical models of leaks, such as pores and cracks is carried out. It is shown that the calculated values of the characteristic parameters are in good agreement with the experimental data. The relationships of parameters of gas expiring by means of through channel such as pressure drop, flow rate, temperatureare obtained in investigation. All parameters are distributed over the volume of the channel, thatallows to trace the nature of the flow and to determine the pointsin which the flow rate movesin the critical region. The obtained data allow us to use the software for mathematical mod-eling of gas flow by means of through defects in abody of vessels of various sizes.

Keywords: through defect, gas velocity, SolidWorks.

Рус

Е. В. Кондратенко (Омский государственный университет путей сообщения (ОмГПС)) E-mail: Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.  

Eng

E. V. Kondratenko (Omsk State Transport University (OSTU)) E-mail: Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.  

Рус

1. Евлампиев А. И., Попов Е. Д., Сажин С. Т., Сумкин П. С. Течеискание / под общ. ред. В. В. Клюева. М.: ИД «Спектр», 2011. 208 с. (Диагностика безопасности).
2. Алямовский А. А. Инженерные расчеты в SolidWorks Simulation. М.: ДМК Пресс, 2010. 464 с. (Проектирование).
3. Прохоренко В. П. SolidWorks. Практическое руководство. М.: ООО «Бином-Пресс», 2004. 448 с.
4. Идельчик И. Е. Справочник по гидравлическим сопротивлениям / под ред. М. О. Штейберга. 3-е изд., перераб. и доп. М.: Машиностроение, 1992. 672 с.
5. Лейбензон Л. С. К теории движения газов. Владивосток: ДАН СССР, 1935. C. 397–398.
6. Белов И. А., Исаев С. А. Моделирование турбулентных течений. СПб.: Балт. гос. техн. ун-т, 2011. 108 с.

Eng

1. Klyuev V.V. (Ed.), Evlampiev A. I., Popov E. D., Sazhin S. T., Sumkin P. S. (2011). Leakage detection. In se-ries «Safety Diagnostics». Moscow: Izdatel'skii dom «Spektr»
2. Aliamovskii A. A. (2010). Engineering calculations in SolidWorks Simulation. Moscow: DMK Press.
3. Prokhorenko V. P. (2004). SolidWorks. Practical guide. Moscow: OOO «Binom-Press».
4. Shteiberg M. O. (Ed.), Idel'chik I. E. (1992). Hand-book of hydraulic resistance. 3rd Ed. (Revised and Supple-mented). Moscow: Mashinostroenie.
5. Leibenzon L. S. (1935). The theory of gas flow. Vladivostok: DAN SSSR, pp. 397–398.
6. Belov I. A., Isaev S. A. (2011). Modeling of turbulent flows. St. Petersburg: Baltiiskii gosudarstvennyi tekhnicheskii universitet.

Рус

Статью можно приобрести в электронном виде (PDF формат).

Стоимость статьи 350 руб. (в том числе НДС 18%). После оформления заказа, в течение нескольких дней, на указанный вами e-mail придут счет и квитанция для оплаты в банке.

После поступления денег на счет издательства, вам будет выслан электронный вариант статьи.

Для заказа статьи заполните форму:

Форма заказа статьи



Дополнительно для юридических лиц:


Type the characters you see in the picture below



.

Eng

This article  is available in electronic format (PDF).

The cost of a single article is 350 rubles. (including VAT 18%). After you place an order within a few days, you will receive following documents to your specified e-mail: account on payment and receipt to pay in the bank.

After depositing your payment on our bank account we send you file of the article by e-mail.

To order articles please fill out the form below:

Purchase digital version of a single article


Type the characters you see in the picture below



 

 

 

 

 

.

.

 

 
Поиск
На сайте?
Сейчас на сайте находятся:
 34 гостей на сайте
Опросы
Понравился Вам сайт журнала?
 
Баннер
Rambler's Top100 Яндекс цитирования